Original Note
The here disclosed 3½ volt, 7 amperage magnet motor/generator must be charged up by
driving the main shaft at 2100 RPM for 42 seconds. This charging process manifests as magnetic
energy within the six coils of copper wire, the copper tube supporting these coils and the copper
coated steel wires wrapped around the magnets. This charging is accomplished while the six coil
connection wires, Part #22, are making contact and setting up their alternating magnetic poles. After
the 42 second charging time one of these coil connection wires must be opened and this circuit
again completed through an energy draw at what could be called 7 amps. See load Part #23. As
current is drawn from the six coils, this draw sets up magnetic poles which are a response between
the rotor magnets and the coils. This response then causes the main shaft to be rotated by the 12
permanent magnets as they attract and build a release field. Then the driver unit (hand crank) is
disconnected allowing the unit to rotate with the load being the activating driving force.
49
The fields of the magnets must be maintained during their spin movement. These magnetic
fields which are encapsulated are achieved by the wiring system. The attract/release of the magnets
is a function of several factors. First, the magnets attract field between north and south is completed
by taking a crossing path of attract (top of one row to bottom of next, etc.). This action has the
effect of fields blending into fields, and a hold—back attract does not happen. Each time a magnet
set passes a coil an interchange of like energy between the coils around the magnets and the
generating coils sets—up neutral polarities which are ‘release fields’ and prevents a hold—back
attract.
One important magnetic assembly is the circuitry which allows this interchange of energy.
This is a recycling of a stabilized magnetic/electro energy not electro/magnetic because the field of
force is not a case of electrical input, an input that created the magnetic energy, but rather a build—
up of magnetic energy which caused an energy thrust.
In further defining the workings of this unit it is important to understand that although electrical
and magnetic (energy) work with similar attitudes, the manner in which they work sets—up a
differing energy effect. One of these effects is that magnetic structures want to share their f1ow,
compatible to the Universal Force, while electrical flow argues, (short circuits, sparks, etc.). Because
of this fact the working responses (within the unit) take place, how they are needed, and when they
are needed which results in a functioning unit. There is a continuous transmutation process taking
place whereby magnetic energy continually generates an energy that manifests a measurable current.
In the past, inventors have sent devices and drawings to Patent Offices claiming they had
invented perpetual motion. This motor, which is driven totally by permanent magnet power, in no
way can be compared with perpetual notion in that the principle is not the same. When perpetual
motion is discussed, it is mentioned in terms of unknown factors which produce an unknown force.
Here, in this Mini Ro—Mag, the force of attract—attract to attract—release within the magnetic
structure can be observed, thereby producing the generating force to turn the rotor which in turn
produces the outflow of power. This power source is not predicated on a continuous flow of energy
but predicated on the consistency of the transmutation process of the magnetic molecular structures
within the Earth's pressure flow.
Some additional points may be useful in understanding the functioning of this unit. The thin
web of brass between the magnets is important because it acts somewhat like a magnetic insulator.
Each section of brass, on the sides of the magnets becomes charged, somewhat like a capacitor. This
builds into a force which TAKES PART in causing the rotations.
The magnets have a particularly low charge, but their charge is only a catalyst at the onset. It
is during the SPIN charging that this blend of alnico elements draws neutral magnetism from the
atmosphere that then manifests with the proper magnet strength for continuous running. This 2.2
peak energy product is the power needed that becomes a point of INCOMING and OUTGOING
magnetic transference. Too much charge would solidify
polarities that would then negate the needed VARIETIES of DIFFERENT magnetic
fields.
This mini-Romag unit cannot run horizontally. The magnetism of the earth system FEEDS
this unit from the top. Gravity is compressed magnetism. The spinning rotor CAPTURES this
compressed magnetism.
Without the copper coated steel wire around the magnets no activity
would take place and here is why. As the rotor is spun, an action that MUST
happen is that the fields around the magnets need to stay with the magnets.
These fields do not manifest as individual flux lines if the magnets are not
wrapped as disclosed. The copper-coated steel wire becomes a MAGNETIC
CONTAINMENT FIELD as these wires take on THEIR OWN charge. These SETUP
fields then serve as ISOLATOR fields which keep the magnets' flux lines in
their place.
The reason these copper-coated steel wires need no insulation is because the
COPPER COATING ITSELF builds into a magnetic flow, which insulates the
primary flow that travels inside the steel portion. This action results in
a magnetic flow circuit that is GUIDED by the activity of the copper
coating. This action should serve as a TEACHING to show how magnetic
current can be sent through conductors that are TOTALLY UNLIKE the standard
electrical insulators. The primary USE of this field (set up by these wires) is that it serves as a
RELEASE AGENT that breaks the elastic hold-back during the generating cycle.
The reason for the U-bent wires is that they serve as a CONDUIT that causes
the magnets flux lines to take their travel path very close to the magnet. This circuit path is around
the back surface and both side edges. This action can be likened to compressing a balloon. The
result is that the field on the front or WORK SURFACE is greatly extended OUTWARD. This
outward extension impacts the copper stator core, which then FEEDS captured magnetic current
into the stator windings.
Sunday, October 14, 2007
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment